Welcome to YUSH Electronic Technology Co.,Ltd.
YUSH Electronic
  English    Chinese
    Fully Automatic Solder Paste Printer
    Detailed Product Description

    Equipment introduction

    Fully Automatic Solder Paste Printer 0
    One. Equipment body
    1. Equipment model YS-G5
    2. Equipment size 1140 (front length) * 1364 side depth) * 1404 (height) mm
    3. Main power supply: AC: 220±10%, 50/60HZ 3KW stable power supply with rated current, plug type: inch. The electrical interface is as shown in the figure above:
    4. Main air supply source: a stable industrial air source with a pressure of 4.0~6kgf/cm², the trachea diameter is 6mm/8mm/10mm/12mm, the front joint of the trachea is universal, and the rear joint only needs to match the size of the trachea
    5. Machine weight: about 900Kg

    Fully Automatic Solder Paste Printer 1
    Two. Equipment use environment
    1. Workshop temperature—20℃~+45℃
    2. Workshop humidity 30-60%
    3. Electrostatic protection: ESD grounding and electrostatic protection are required
    4. If the equipment is not used on the first floor, please pay attention to the heavy load-bearing of the floor, and the load-bearing must be ≥650kg/m²

     

    Machine Performance
    Repeat Position Accuracy±0.01mm
    Print Accuracy±0.025mm
    NCP-CT7.5s
    HCP-CT19s/pcs
    Process CT5min
    Transfer line CT3min
    Substrate processing parameter
    Max9∶27imum board size400*340mm Scalable:530*340mm(Options)
    Minimum board size50*50mm
    Board thickness0.4-6mm
    Camera Mechanical range528*340mm
    Maximum board weight3kg
    Board edge clearance2.5mm
    Board height15mm
    Transport speed900±40mm
    (Max)Transport speedSegment control 1500mm/s(Max)
    Transport directionOne-section transport rail
    Transmission directionLeft to right
    Right to Left
    In and out the same
    Support SystemMagnetic Pin
    Support Block
    Manual Up-down table
    Board clampAutomatic top clamping
    Side clamping
    Adsorption function
    Printing Parameters
    Print Speed10~200mm/sec
    Print Pressure0.5~10Kg
    Print ModeSingle or double doctor blade printing
    Queegee Type(09/s5/st alfue) apels apels ofoonbs/mand (09/ss/stalle) Chiell/Dievilievi
    Snap-off0~20mm
    Snap-Speed0~20mm/sec
    The template frame size470*370mm~737*737mm(Thickness∶20-40mm)
    Steel mesh positioning methodAutomatic Y-direction positioning (compatible with manual compensation adjustment)
    Cleaning Parameters
    Cleaning SystemDry, Wet Vacuum three modes
    Cleaning systemUp Drip type
    Cleaning strokeAutomatic generation
    Cleaning positionPost cleaning
    Cleaning Speed10-200mm/sec
    Cleaning fluid consumptionAuto & Manually adjustable
    Cleaning paper consumptionAuto & Manually adjustable
    Vision Parameters
    CCD FOV10*8mm
    Camera type130 Thousand CCD Digital camera
    Camera SystemLock up/down optics structure
    Camera Cycle time300ms
    Fiducial mark typesStandard Fiducial Mark Shape
    Round,square,diamond,cross
    Pad and profile
    Mark size0.5-5mm
    Mark numberMax:4pcs
    Stay away numberMax: 1pcs
    Smart equipment
    safely controlDoor open to stop, abnormal alarm
    2D inspectionDetection of less tin/missing print/continuous tin
    Automatic crimpingAutomatically push up the guide rail
    Vacuum adsorptionPlatform vacuum adsorption
    Machine parameter
    Power SourceAC:220±10%,50/60Hz2.2KW
    Air Pressure4~6Kgf/cm²
    Air ConsumptionAbout 5L/min
    Operating Temperature-20℃~+45℃
    Working environment humidity30%~60%
    Machine dimension (without Tower light)1404(H)mm
    Machine Length1140(L)mm
    Machine Width1364(W)mm
    Machine Weight ApproxApprox∶About900Kg
    Equipment load bearing requirements650Kg/㎡


    Product Categories
                                              Fully Automatic Solder Paste Printer
                                              Fully Automatic Solder Paste Printer
                                              Fully Automatic Solder Paste Printer
                                               
                                              Detailed Product Description

                                              Equipment introduction

                                              Fully Automatic Solder Paste Printer 0
                                              One. Equipment body
                                              1. Equipment model YS-G5
                                              2. Equipment size 1140 (front length) * 1364 side depth) * 1404 (height) mm
                                              3. Main power supply: AC: 220±10%, 50/60HZ 3KW stable power supply with rated current, plug type: inch. The electrical interface is as shown in the figure above:
                                              4. Main air supply source: a stable industrial air source with a pressure of 4.0~6kgf/cm², the trachea diameter is 6mm/8mm/10mm/12mm, the front joint of the trachea is universal, and the rear joint only needs to match the size of the trachea
                                              5. Machine weight: about 900Kg

                                              Fully Automatic Solder Paste Printer 1
                                              Two. Equipment use environment
                                              1. Workshop temperature—20℃~+45℃
                                              2. Workshop humidity 30-60%
                                              3. Electrostatic protection: ESD grounding and electrostatic protection are required
                                              4. If the equipment is not used on the first floor, please pay attention to the heavy load-bearing of the floor, and the load-bearing must be ≥650kg/m²

                                               

                                              Machine Performance
                                              Repeat Position Accuracy±0.01mm
                                              Print Accuracy±0.025mm
                                              NCP-CT7.5s
                                              HCP-CT19s/pcs
                                              Process CT5min
                                              Transfer line CT3min
                                              Substrate processing parameter
                                              Max9∶27imum board size400*340mm Scalable:530*340mm(Options)
                                              Minimum board size50*50mm
                                              Board thickness0.4-6mm
                                              Camera Mechanical range528*340mm
                                              Maximum board weight3kg
                                              Board edge clearance2.5mm
                                              Board height15mm
                                              Transport speed900±40mm
                                              (Max)Transport speedSegment control 1500mm/s(Max)
                                              Transport directionOne-section transport rail
                                              Transmission directionLeft to right
                                              Right to Left
                                              In and out the same
                                              Support SystemMagnetic Pin
                                              Support Block
                                              Manual Up-down table
                                              Board clampAutomatic top clamping
                                              Side clamping
                                              Adsorption function
                                              Printing Parameters
                                              Print Speed10~200mm/sec
                                              Print Pressure0.5~10Kg
                                              Print ModeSingle or double doctor blade printing
                                              Queegee Type(09/s5/st alfue) apels apels ofoonbs/mand (09/ss/stalle) Chiell/Dievilievi
                                              Snap-off0~20mm
                                              Snap-Speed0~20mm/sec
                                              The template frame size470*370mm~737*737mm(Thickness∶20-40mm)
                                              Steel mesh positioning methodAutomatic Y-direction positioning (compatible with manual compensation adjustment)
                                              Cleaning Parameters
                                              Cleaning SystemDry, Wet Vacuum three modes
                                              Cleaning systemUp Drip type
                                              Cleaning strokeAutomatic generation
                                              Cleaning positionPost cleaning
                                              Cleaning Speed10-200mm/sec
                                              Cleaning fluid consumptionAuto & Manually adjustable
                                              Cleaning paper consumptionAuto & Manually adjustable
                                              Vision Parameters
                                              CCD FOV10*8mm
                                              Camera type130 Thousand CCD Digital camera
                                              Camera SystemLock up/down optics structure
                                              Camera Cycle time300ms
                                              Fiducial mark typesStandard Fiducial Mark Shape
                                              Round,square,diamond,cross
                                              Pad and profile
                                              Mark size0.5-5mm
                                              Mark numberMax:4pcs
                                              Stay away numberMax: 1pcs
                                              Smart equipment
                                              safely controlDoor open to stop, abnormal alarm
                                              2D inspectionDetection of less tin/missing print/continuous tin
                                              Automatic crimpingAutomatically push up the guide rail
                                              Vacuum adsorptionPlatform vacuum adsorption
                                              Machine parameter
                                              Power SourceAC:220±10%,50/60Hz2.2KW
                                              Air Pressure4~6Kgf/cm²
                                              Air ConsumptionAbout 5L/min
                                              Operating Temperature-20℃~+45℃
                                              Working environment humidity30%~60%
                                              Machine dimension (without Tower light)1404(H)mm
                                              Machine Length1140(L)mm
                                              Machine Width1364(W)mm
                                              Machine Weight ApproxApprox∶About900Kg
                                              Equipment load bearing requirements650Kg/㎡


                                              Online Message
                                              Welcome message, we will reply within 24 hours!
                                              *Subject:
                                              *Your E-Mail:
                                              (Please make sure your E-mail address is correct.
                                              Else, the receiver cannot reply you afterwards. )

                                              Content:
                                              *Country/Region:
                                              Your Company:
                                              Your Name:
                                              Tel:
                                              Fax:
                                              YUSH Electronic Technology Co.,Ltd. Pomeas Optical Technology Copyright 2016
                                              CONTACT US
                                              Contacts:Eva Liu +86 13416743702
                                              Tel:+86-512-62751429
                                              Skype:evaliuhuan
                                              Email:sales@yushunli.com evaliu@hk-yush.com
                                              Company Address:Address: Building H, GuoRui Pioneering
                                              Park, No. 1068 Jinyang East Road, Lujia Town, Kunshan,
                                              Suzhou,Jiangsu,China.
                                              Postcode:215331
                                              YUSH Electronic Technology Co.,Ltd. Pomeas Optical Technology Copyright 2016