Automatic soldering machine maintenance method
First, the necessary pre-boot inspection, first from the power supply, check whether the tin wire is used up and the soldering iron is damaged; whether the tin wire is used up.
Second, the normal tin wire should be placed in a dry, cool place to avoid moisture or excessive temperature. When it is wet, the solder will touch the tip and there will be a small tinning phenomenon.
Third, when the tin wire is used up, it is recommended that you cut the tin wire at the front end of the tin feeder, and pull it out from the front section of the tin pipe (near the tip of the soldering iron) to avoid blocking the tin pipe or tin wire. Inside the tube to reduce the time you need to change the tin wire.
Fourth, it is strictly forbidden to turn off the power when the machine is turned on. This will easily damage the machine, and the service life of the machine will be much reduced. You should turn off the power first and turn off the power.
Fifth, after the end of each day's work, it is recommended that you use alcohol to clean the soldering iron and the flux in the front section of the tin tube (near the soldering iron tip) to facilitate the smooth operation of the next day.
Sixth, customers who use anti-tin blasting tinware generally check whether the teeth on the broken tin blade are damaged in about three months, so as not to affect the use effect of anti-tin blast.
Seventh, when replacing the tin wire, please ensure that the tin wire is placed in the correct position of the tin feeding gear, and at the same time, the tin feeding tube should be locked to avoid loosening during the tin feeding process, thereby increasing the corresponding tin feeding failure, thereby Extend your precious time.
Eighth, when replacing the tip, please turn off the power of the whole machine, and the power of the temperature controller is also turned off, and ensure that the temperature of the soldering iron has dropped to the touchable range, so as to avoid damage to the soldering iron or occur. scald.
Ninth, it is strictly forbidden to touch the soldering iron tip and the lower tin wire by hand during the whole process of welding to avoid burns. During the operation of the machine, it is strictly forbidden to penetrate any part of the body into the running area of the machine to avoid unnecessary accidents (self-defense awareness is strong, no dozing is allowed)
Automatic soldering machine maintenance method
First, the necessary pre-boot inspection, first from the power supply, check whether the tin wire is used up and the soldering iron is damaged; whether the tin wire is used up.
Second, the normal tin wire should be placed in a dry, cool place to avoid moisture or excessive temperature. When it is wet, the solder will touch the tip and there will be a small tinning phenomenon.
Third, when the tin wire is used up, it is recommended that you cut the tin wire at the front end of the tin feeder, and pull it out from the front section of the tin pipe (near the tip of the soldering iron) to avoid blocking the tin pipe or tin wire. Inside the tube to reduce the time you need to change the tin wire.
Fourth, it is strictly forbidden to turn off the power when the machine is turned on. This will easily damage the machine, and the service life of the machine will be much reduced. You should turn off the power first and turn off the power.
Fifth, after the end of each day's work, it is recommended that you use alcohol to clean the soldering iron and the flux in the front section of the tin tube (near the soldering iron tip) to facilitate the smooth operation of the next day.
Sixth, customers who use anti-tin blasting tinware generally check whether the teeth on the broken tin blade are damaged in about three months, so as not to affect the use effect of anti-tin blast.
Seventh, when replacing the tin wire, please ensure that the tin wire is placed in the correct position of the tin feeding gear, and at the same time, the tin feeding tube should be locked to avoid loosening during the tin feeding process, thereby increasing the corresponding tin feeding failure, thereby Extend your precious time.
Eighth, when replacing the tip, please turn off the power of the whole machine, and the power of the temperature controller is also turned off, and ensure that the temperature of the soldering iron has dropped to the touchable range, so as to avoid damage to the soldering iron or occur. scald.
Ninth, it is strictly forbidden to touch the soldering iron tip and the lower tin wire by hand during the whole process of welding to avoid burns. During the operation of the machine, it is strictly forbidden to penetrate any part of the body into the running area of the machine to avoid unnecessary accidents (self-defense awareness is strong, no dozing is allowed)
